Pentair Jung Pumpen Omnia Stainless Steel Vortex Pumps
The Pentair Jung Pumpen Omnia range is a family of compact stainless steel vortex pumps for dirty water that carries soft solids. Three sizes, the Omnia 80/5, 160/7 and 200/8, cover rainwater sumps, flooded cellars and plant rooms, light industrial tanks and water features, with up to 200 litres per minute from the largest model. All three share a 1¼” outlet and pass solids up to 20 mm.
The pump housing, motor housing and impeller are AISI 304 stainless steel, so the Omnia resists the rust that builds up on cast iron pumps left standing in wet sumps. Jung Pumpen fits an oil chamber, self-lubricating ball bearings and a motor cooled by a heat exchange chamber, which lets the pump run for long periods without being fully submerged. Each pump comes with 10 metres of H07RN-F cable and a 32 mm hose connector.
How the Omnia vortex impeller handles dirty water
A vortex impeller sits recessed above the pump inlet. It spins the water into a whirlpool, and that swirl carries grit, leaves and soft debris out through the outlet without most of it ever touching the impeller vanes. The result is a pump that is far less prone to clogging in dirty water than a standard drainage impeller, at the cost of a little efficiency.
Choosing between the Omnia 80/5, 160/7 and 200/8
The two numbers in each name are the rated flow in litres per minute and the head in metres. The 80/5 suits small sumps and light duty; the 160/7 is the mid-size pump for cellars and soakaway chambers; the 200/8 moves the most water and lifts it highest. Head matters more than the headline flow: at 4 metres of lift the 80/5 delivers only about 12 l/min, while the 200/8 still gives around 100 l/min.
Manual models run whenever power is on. Automatic models have a float switch that starts and stops the pump with the water level. The 80/5 and 200/8 come in 230v and 110v for site use; the 160/7 is 230v only.
| Model | Versions | Rated Flow (l/min) | Rated Head (m) | Flow at 2 m (l/min) | Flow at 4 m (l/min) | Motor P2 (kW) | Weight (kg) |
|---|---|---|---|---|---|---|---|
| Omnia 80/5 | 230v or 110v, manual or automatic | 80 | 5 | 53 | 12 | 0.2 | 6.1 |
| Omnia 160/7 | 230v, manual or automatic | 150 | 7 | 117 | 70 | 0.37 | 7.0 |
| Omnia 200/8 | 230v or 110v, manual or automatic | 200 | 8 | 157 | 103 | 0.5 | 8.5 |
Flows at 2 m and 4 m are converted from Jung Pumpen’s published performance data; Pentair rates the 160/7 at 150 l/min. Click through to any model for its versions and full specifications.
Showing 19-28 of 10 results
80 l/min · 5 m · 230v
Stainless steel vortex pump for dirty water with soft solids up to 20 mm. Rated 80 l/min and 5 ...Read More£319.60 +VAT
80 l/min · 5 m · 230v
Automatic stainless steel vortex pump with integral float switch, for dirty water with soft solids up to 20 mm. ...Read More£334.09 +VAT
80 l/min · 5 m · 110v
110v stainless steel vortex pump for site drainage of dirty water with soft solids up to 20 mm. Rated ...Read More£319.60 +VAT
80 l/min · 5 m · 110v
Automatic 110v stainless steel vortex pump with integral float switch, for dirty water with soft solids up to 20 ...Read More£334.09 +VAT
150 l/min · 7 m · 230v
Mid-size stainless steel vortex pump for dirty water with soft solids up to 20 mm. Up to 150 l/min ...Read More£374.11 +VAT
150 l/min · 7 m · 230v
Automatic stainless steel vortex pump with integral float switch, for dirty water with soft solids up to 20 mm. ...Read More£388.60 +VAT
200 l/min · 8 m · 230v
The largest Omnia stainless steel vortex pump, for dirty water with soft solids up to 20 mm. Rated 200 ...Read More£437.59 +VAT
200 l/min · 8 m · 230v
Automatic stainless steel vortex pump with integral float switch, for dirty water with soft solids up to 20 mm. ...Read More£452.08 +VAT
200 l/min · 8 m · 110v
110v stainless steel vortex pump for site drainage of dirty water with soft solids up to 20 mm. Rated ...Read More£437.59 +VAT
200 l/min · 8 m · 110v
Automatic 110v stainless steel vortex pump with integral float switch, for dirty water with soft solids up to 20 ...Read More£452.08 +VAT
Where to Use Omnia Vortex Pumps
Jung Pumpen designs the Omnia for rainwater, drain water and waste water: draining infiltrated groundwater, lifting rainwater from gullies and wells, emptying flooded rooms, tanks and light industrial pits, and running fountains and water features. Muddy water with silt, leaves and soft debris up to 20 mm is exactly the job a vortex pump does well, because the solids swirl past the impeller instead of jamming in it. Our guide to what a dirty water pump is explains when you need one.
Size the pump on the lift as well as the flow. Measure the height from the water to the discharge point, add an allowance for hose length, then read across the duty figures in the table above. Our guide to pump head and flow rate shows how to work this out. For an unattended sump, choose an automatic model, or add a separate float switch to a manual one.
Know where the Omnia stops. For clean or lightly soiled water where solids handling matters less, look at the Pentair Jung Drenox stainless steel drainage pumps. For raw sewage, toilet waste and larger solids, step up to the Pentair Jung Nocchi Priox sewage pumps.
Frequently Asked Questions
What is a vortex impeller and why does the Omnia use one?
A vortex impeller is recessed into the top of the pump chamber rather than sitting in the flow path. It creates a whirlpool that carries the water and any solids out of the outlet, so debris rarely touches the vanes. That makes the Omnia much harder to block in dirty water than a pump with a standard drainage impeller.
What size solids can an Omnia pump pass?
Every Omnia has a free passage of 20 mm, meaning soft solids up to that size pass through the pump. Keep stones, rag and fibrous material out of the sump.
Can the Omnia pump sewage or toilet waste?
No. The Omnia is a dirty water pump for rainwater, drain water and waste water, and its 20 mm passage is too small for raw sewage. Jung Pumpen also states it must not be used for flammable or dangerous liquids. For toilet waste, use a dedicated sewage pump such as the Priox range.
How low will an Omnia pump the water?
The pump needs a starting level of about 80 mm (80/5) or 96 mm (160/7 and 200/8) to prime, according to Jung Pumpen’s manual. Once running, it keeps drawing down to a minimum level of 35 mm. It must never run dry, so a manual pump should be switched off once the water is gone.
When does the automatic Omnia switch on and off?
Jung Pumpen gives these float levels: the 80/5 automatic starts at 250 mm and stops at 100 mm, the 160/7 at 320 mm and 107 mm, and the 200/8 at 351 mm and 111 mm. Your sump needs to be deep enough for the float to rise to its start level, and the pump should not start more than 30 times an hour.
Is there a 110v Omnia 160/7?
Not in our range. The Omnia 80/5 and 200/8 are available in 110v for site transformers, manual or automatic; the 160/7 is supplied in 230v only.
If you would like help choosing an Omnia for a sump, cellar or site, call the AES Rewinds team on 01252 515169 or email sales@aesrewinds.com. You can also browse all dirty water pumps.
Free, independent advice
Need help choosing? Ask our team
Not sure it is the right pump or motor for the job? Send us a question and our team will reply, or call us now. We have been supplying, repairing and rewinding pumps since 1948.
Monday to Friday, 8.30am to 5.30pm
Send us a question
We reply within one working day.










