Pentair Dominator 230v 4" Well Pumps

The Pentair Dominator 4″ well pump is a 230v single-phase multistage submersible pump for clean water in 4-inch wells and boreholes. It sits below the water level, so there is nothing to prime, and its eight stacked impellers give it the pressure to lift water from depth and feed a house supply, a storage tank or an irrigation system.

The Dominator 4″ range has now been discontinued. All three models, the 55/50, 75/56 and 115/57 M, are no longer available, and the details on this page are kept for reference if you are maintaining or replacing one. For a 4-inch bore, the Matra Venus borehole pumps are the ones to look at, or call us on 01252 515169 and we can advise on the best replacement for your bore.

Dominator 4″ 115/57 M performance

The 57 in the model name is the maximum head in metres, reached at zero flow. As the flow rises the head falls: Pentair’s figures give 52 metres at 20 litres per minute, 44.4 metres at 40 l/min and 16.6 metres at 80 l/min. If you are choosing a replacement, compare its curve against these figures at the head your installation needs. Our guide on how to read a pump curve explains the method.

The pump is driven by a 0.8 kW sealed dry motor, cooled by the water around it, with the capacitor built in and a thermal cut-out in the winding. It is IP68 rated and suitable for continuous duty. The pump body is AISI 304 stainless steel, the impellers are acetal resin and the diffusers are polycarbonate with ceramic inserts at the wear points. A non-return valve is built into the pump.

Sizing a replacement for your borehole

The Dominator 4″ is 98 mm in diameter and 643 mm long. A 4-inch bore leaves very little room around a pump for the power cable, so measure the internal diameter of your casing before you order a replacement. For a 3-inch bore, look at the Pentax 3S 3-inch borehole pumps instead.

Flow (l/min)020406080
Head, Dominator 4″ 115/57 M (m)575244.431.516.6

Figures from Pentair’s published data for the 115/57 M: 230v single-phase, 0.8 kW, 5 A, eight stages, 1¼” outlet, 20 m power cable. For clean water up to 40°C only.

Showing all 3 results

Where the Dominator 4″ Well Pump Was Used

Pentair designed the Dominator 4″ for pumping from wells and boreholes, supplying domestic pressure systems with a tank, and small automatic or larger irrigation systems. Typical jobs are a private borehole supply to a rural house or outbuilding, filling a header or storage tank on higher ground, or watering a large garden, paddock or allotment from a well.

When you replace one, size the new pump against the whole installation, not just the depth of the water. Add the depth to the water level while the pump is running, the height from the top of the bore to the highest outlet or tank, the friction loss in the pipe and the pressure you want at the tap (10 metres of head is roughly 1 bar). Then check the flow the new pump gives at that head. Our guide to pump head and flow rate walks through the sums, and how to select the right well and borehole pump covers the wider choice.

The 115/57 M has no float switch, so it runs whenever it has power. For a pressurised house supply it is normally paired with a pressure switch and pressure vessel, or with a level control when it is filling a tank. You can compare current options in our well and borehole pumps category.

Frequently Asked Questions

Is the Dominator 4″ still available?

No. Pentair’s Dominator 4″ range, including the 115/57 M, has been discontinued. For a 4-inch bore, look at the Matra Venus borehole pumps, or tell us your bore diameter, the depth to the water and the flow you need and we will suggest a replacement.

Will a replacement fit in a 4-inch borehole?

The Dominator 4″ has a 98 mm body. A 4-inch bore is about 102 mm, which leaves little room for the power cable running down beside the pump. Measure the internal diameter of your casing, and if it is tight or partly blocked, talk to us before you order.

How deep was the pump installed?

It came with 20 metres of power cable and a 20 metre nylon suspension cord. Hang any borehole pump on the cord or the delivery pipe, never by the power cable, and keep it clear of any silt at the bottom of the bore.

Does it need a separate non-return valve?

The pump has a non-return valve built in, which stops water in the rising main draining back down the bore when the pump stops. Whether you need extra valves elsewhere depends on your pipework and controls.

Can the Dominator 4″ pump sandy or dirty water?

No. Pentair specifies clean water only, up to 40°C, with no suspended solids or abrasive material. If your borehole produces sand, it needs dealing with before a pump like this goes in.

Can I use a Dominator 5″ instead?

The Pentair Dominator 5″ well pumps are 132 mm across, so they will not go down a 4-inch or 5-inch borehole and suit open wells and tanks instead. For a 4-inch bore, the Matra Venus borehole pumps are the ones to compare.

For help choosing a replacement borehole pump, call the AES Rewinds team on 01252 515169 or email sales@aesrewinds.com. Tell us the bore diameter, the depth to the water, the height to your highest outlet and the flow you need.

Free, independent advice

Need help choosing? Ask our team

Not sure it is the right pump or motor for the job? Send us a question and our team will reply, or call us now. We have been supplying, repairing and rewinding pumps since 1948.

Monday to Friday, 8.30am to 5.30pm

Send us a question

We reply within one working day.

Loading cart