Matra Venus Borehole Well Pumps

The Matra Venus is a 4-inch submersible borehole pump for clean water, built for jobs that need high pressure rather than high volume. Matra designs it to lift water from wells, boreholes and tanks for garden irrigation and to boost pressure in a domestic supply. Both models run on 230v single-phase mains and deliver up to 50 litres per minute through a 1″ outlet.

Unlike most 4-inch borehole pumps, which stack several small impellers, the Venus uses a single peripheral impeller. Vanes around the rim of the impeller push the water again and again as it travels round the channel in the pump casing, which builds a lot of pressure at low flow. The pump body and impeller are brass, the outer shell and shaft are AISI 304 stainless steel, and a non-return valve is built in. The motor is oil-cooled with Class B insulation.

Every Venus is supplied with a control box housing the motor’s capacitor and thermal overload protection, so on a single-phase supply you do not need to source these separately.

Venus 100 or Venus 180?

The two pumps share the same 98 mm body and the same flow range. The difference is the motor and the pressure it produces.

The Venus 100 has a 0.75 kW (1 HP) motor. Matra’s figures give 47 metres of head at 5 l/min, 37 metres at 20 l/min and 25 metres at 30 l/min. It suits a garden irrigation system or a modest lift from a shallow borehole.

The Venus 180 has a 1.33 kW (1.8 HP) motor and roughly doubles the head at every flow: 87 metres at 5 l/min, 69 metres at 20 l/min and 48 metres at 30 l/min. Choose it when the water level is deep, the delivery pipe climbs a long way, or you want good pressure at the tap from a deep source.

On both models the head falls steeply as the flow rises, so read the figures at the flow you actually need.

ModelMotor P2 (kW)Head at 5 l/min (m)Head at 20 l/min (m)Head at 30 l/min (m)Head at 40 l/min (m)Head at 50 l/min (m)Length x Dia (mm)Weight (kg)
Matra Venus 1000.75473725155460 x 9815
Matra Venus 1801.338769482810500 x 9818

Both models are 230v single-phase with a 1″ G outlet. Figures are from Matra’s published performance data. Click through to either model for its full specification.

Showing all 2 results

Where to Use Matra Venus Borehole Pumps

Matra designs the Venus to lift clean water from wells, boreholes and tanks, to irrigate gardens and to boost pressure in domestic systems. Typical jobs are a private borehole feeding a garden or smallholding, a well supplying a pressure vessel for a house, or a tank where water must climb a long delivery pipe.

The Venus works best where you need a modest flow at a high head. A drip or sprinkler line drawing 15 to 25 l/min, or a single property filling a pressure vessel, plays to its strengths. If several outlets will run at once and you need 40 l/min or more, the head drops away quickly, so check the figures above against your demand. Our guide to pump head and flow rate shows how to add up the total head, and how to select the right well and borehole pump covers the wider choice.

The Venus is for clean water only. Peripheral pumps run with very fine clearances, so sand and silt wear them quickly. For a 3-inch bore, see the Pentax 3S 3-inch borehole pumps, and for open wells and tanks needing more flow, the Pentair Dominator 5″ well pumps. You can compare everything in our well and borehole pumps category.

Frequently Asked Questions

How wide does my borehole need to be for a Matra Venus?

The Venus is a 4-inch pump with a 98 mm body, made for 4-inch wells and boreholes or wider. In a 4-inch bore that leaves very little room for the power cable to pass the pump, and Matra does not publish a minimum bore size. Measure the internal diameter of your casing before you order, and call us if it is close.

What is a peripheral impeller pump?

A peripheral (sometimes called regenerative) pump has a single impeller with many small vanes cut around its rim. The water is pushed by the vanes repeatedly as it passes round the casing, so one impeller can produce the kind of head a multistage pump needs several stages to reach. The trade-off is a steep curve: on the Venus 180, head falls from 69 metres at 20 l/min to 28 metres at 40 l/min.

Does the Venus come with a control box?

Yes. Matra supplies each Venus with a control box that houses the capacitor and thermal overload protection for the single-phase motor. It does not switch the pump on and off with demand, so for an automatic water supply you will also need a pressure switch and pressure vessel, or a level control in the well.

Is the Venus 100 or the Venus 180 right for me?

Work out the total head first: the depth to the water when the pump is running, plus the height to your highest outlet, plus pipe friction and the pressure you want at the tap (10 metres is roughly 1 bar). If that comes to 30 metres or less at around 25 l/min, the Venus 100 will cope. Above that, or for deep water levels, choose the Venus 180, which still gives 58 metres at 25 l/min.

Does the Venus have a non-return valve?

Yes. Matra builds a non-return valve into both models, which stops the water in the rising main draining back down the borehole when the pump stops.

For help choosing between the Venus 100 and the Venus 180, or comparing them with another 4-inch borehole pump, call the AES Rewinds team on 01252 515169 or email sales@aesrewinds.com. Tell us the bore diameter, the depth to the water and the height to your highest outlet.

Free, independent advice

Need help choosing? Ask our team

Not sure it is the right pump or motor for the job? Send us a question and our team will reply, or call us now. We have been supplying, repairing and rewinding pumps since 1948.

Monday to Friday, 8.30am to 5.30pm

Send us a question

We reply within one working day.

Loading cart