GMP RED High Volume Diesel Fuel Transfer Pumps with ATEX Motors

The GMP RED ATEX diesel transfer pumps are self-priming centrifugal pumps for moving diesel and gas oil in bulk where a potentially explosive atmosphere may be present: fuel stores, tank farms, refuelling points, generator day tanks and plant rooms covered by a DSEAR assessment. Seven models run from a 1½-inch pump at 285 litres per minute up to a 3-inch pump at 1,250 litres per minute, far more than the small drum and dispenser pumps most ATEX fuel pumps are built around.

GMP’s declaration of conformity marks these pumps II 2 G Ex h IIB T4 Gb under ATEX Directive 2014/34/EU, with a maximum liquid temperature of +50°C. Each pump has a cast iron pump body, valve body, impeller and motor support, a monobloc build with a multi-blade open impeller, an AISI 316 stainless steel motor shaft and a Viton, carbon and alumina mechanical seal. A non-return valve inside the pump body stops it draining after shutdown, so it is ready to prime again from up to 6 metres of suction lift.

Choosing an ATEX diesel pump from the range

The number after the “B” is the port size in inches: B1½, B2 and B3 pumps have matching inlet and outlet threads of that size. The KQ-A models are the standard pump end, and the B3XR-A is the larger 4 kW pump that lifts higher and moves the most fuel.

The four-character GMP code tells you the motor. EAZ3, EA9D and EA9E are 230v single-phase versions for sites without a three-phase supply. 2140, 2141, 2138 and 2139 are three-phase 400v versions, which draw far less current and suit fixed installations on an industrial supply.

As a starting point, a B1½ pump suits filling bowsers, generators and small storage tanks, a B2 pump is the general bulk transfer size, and the B3KQ-A suits tanker offloading and high-volume transfer at moderate head. Choose the B3XR-A RED 2139 where you need both high flow and up to 28.5 metres of head, such as long or elevated delivery lines.

ModelSupplyPortsMotor (kW)Max Flow (l/min)Max Head (m)Max Solids (mm)
B1½KQ-A RED EAZ3230v single-phase1½”0.75285168.5
B1½KQ-A RED 2140400v three-phase1½”0.75285168.5
B2KQ-A RED EA9D230v single-phase2″1.54501916
B2KQ-A RED 2141400v three-phase2″1.54501916
B3KQ-A RED EA9E230v single-phase3″2.29001627
B3KQ-A RED 2138400v three-phase3″2.29001627
B3XR-A RED 2139400v three-phase3″4.01,25028.519

Flow and head are GMP’s published maximums for each ATEX model. Click through to any model for its full specifications.

Showing all 7 results

Where to Use ATEX Diesel Transfer Pumps

An ATEX pump is the right choice wherever your risk assessment under DSEAR (the Dangerous Substances and Explosive Atmospheres Regulations) classifies the area around the pump as a hazardous zone. Typical installations include bulk fuel stores and bunded tank compounds, tanker offloading points, generator and boiler fuel systems, refuelling areas for plant and fleet vehicles, and enclosed pump rooms where vapour can collect.

These are surface-mounted, self-priming pumps, so they sit beside or above the tank and draw fuel up through the suction line, with up to 6 metres of suction lift once the pump casing has been filled. Keep the suction line short, airtight and at least the size of the pump inlet, because every metre of lift and pipe friction reduces what the pump can deliver. Our guides to how self-priming pumps work and suction lift and NPSH explain how to set one up so it primes reliably.

If the pump will run in a safe area, such as an open yard or a well ventilated building outside any classified zone, you do not need to pay for ATEX equipment. The standard GMP RED diesel transfer pumps use the same pump sizes with conventional motors and add 1-inch and 110v models. You can also browse all self-priming pumps.

Frequently Asked Questions

What does the ATEX marking II 2 G Ex h IIB T4 Gb mean?

II is equipment group II (surface industries rather than mining) and 2 G is category 2 for gas atmospheres, the category intended for Zone 1 areas and also accepted in Zone 2. Ex h is the protection type for non-electrical equipment, IIB is the gas group, T4 limits the maximum surface temperature to 135°C, and Gb is the matching equipment protection level. GMP’s declaration also sets a maximum liquid temperature of +50°C.

Can these pumps be used in Zone 1?

Category 2 G equipment is designed for Zone 1 and Zone 2 gas areas, but not Zone 0. The zone itself comes from your DSEAR risk assessment, so check the rating plates and the documents supplied with the pump against that assessment before installation. Because the gas group is IIB, these pumps are not for atmospheres classed IIC, such as hydrogen or acetylene.

Are the motors flameproof (Ex d)?

GMP’s published datasheets and declaration give the ATEX marking for the pump unit, not a separate protection type for the motor. If your assessment or your client’s specification requires a particular motor protection concept, such as flameproof Ex d, ask us for the motor certificate for the exact model before you order.

Can I pump petrol with a GMP RED ATEX pump?

No. This range is supplied for diesel and gas oil transfer and is not suitable for petrol. Petrol needs a pump specified for it, so call us if you need to move petrol, kerosene or another fuel and we will advise on the right equipment.

Should I choose the 230v or 400v version?

Both versions of each size have the same pump end, flow and head. Choose 230v single-phase (EAZ3, EA9D or EA9E) where only a single-phase supply is available, and 400v three-phase (2140, 2141 or 2138) on an industrial supply, where the lower running current makes cable sizing easier. The largest model, the B3XR-A RED 2139, is three-phase only.

ATEX selection depends on your zone, your fuel and your installation, so if you are unsure which model fits, call the AES Rewinds team on 01252 515169 or email sales@aesrewinds.com. You can also browse the full GMP pump range or all surface mounted pumps.

Free, independent advice

Need help choosing? Ask our team

Not sure it is the right pump or motor for the job? Send us a question and our team will reply, or call us now. We have been supplying, repairing and rewinding pumps since 1948.

Monday to Friday, 8.30am to 5.30pm

Send us a question

We reply within one working day.

Loading cart